徳さんSPブルーイング、2/2
Bluing by Toku-san, 2/2
徳さんSPブルーイング、2/2_a0077842_721474.jpg
▲右が目立て後のシリンダーラッチ。鋭いエッジを鋳物で再現するのは難しいので/The cylinder latch after being set from the right. This detailed manufacturing cannot be reproduced by zinc die casting.
徳さんSPブルーイング、2/2_a0077842_7273873.jpg
▲レーザーサイトの赤の矢印で示した部分のエッジを和らげる。この微妙なカーブは量産の挽き物加工では再現できないということで断念している部分なのだ。右が加工後/Soften the section of the edge indicated in red on the laser sight. This delicate curve cannot be reproduced on mass production grinding machinery, therefore some sections must be abandoned. The right shows the situation after manufacturing.
徳さんSPブルーイング、2/2_a0077842_8493881.jpg
▲トリガーガードの加工。右が加工後/Manufacturing the trigger guard. The right shows after manufacturing.





徳さんSPブルーイング、2/2_a0077842_8495684.jpg
▲ライトカバーの底部の段差を溝に変更する/Change the bottom layers of the right cover into grooves.
徳さんSPブルーイング、2/2_a0077842_854555.jpg
▲マイナスネジを新造する。量産の挽き物加工で作られたネジの頭にはわずかに同心円状の加工痕があり、磨くより早いということで新造した/Newly produce the minus screws. The tops of minus screws produced by mass production grinding machinery will have slight traces of concentric circles, and these can be newly produced faster than by the polishing processes.
徳さんSPブルーイング、2/2_a0077842_859319.jpg
▲ダミ・プライマーを削り出す/Cut out a new dummy primer.
徳さんSPブルーイング、2/2_a0077842_903224.jpg
▲弾丸や薬莢とともに研磨する。右が加工後/with that grind new items like bullets and cartridges. The right shows after manufacturing.
徳さんSPブルーイング、2/2_a0077842_934970.jpg
▲露出する主要なネジ類を研磨する/Grind the screw types important for exposure.
徳さんSPブルーイング、2/2_a0077842_951671.jpg
▲宝石のように磨き上げられたレシーバー回り/Turning the receiver that has been polished like a jewel.
徳さんSPブルーイング、2/2_a0077842_96522.jpg
▲ブルーイング処理後のレシーバー回り/Turning the receiver after bluing.
徳さんSPブルーイング、2/2_a0077842_972265.jpg
▲HW・プラスチック製チャーターアームズのフレームを研磨する/Grind the frame for the heavy weight plastic Charter Arms.
徳さんSPブルーイング、2/2_a0077842_9102691.jpg
▲ブルーイング処理後のフレーム/Turning the frame after bluing.


by tomenosuke_2006 | 2015-05-29 09:13 | 留之助ブラスター
<< スクリーミング・ハンド、発売は... ミニ・アクセサリーもルークが作... >>